How to prevent oil leakage of the generator set when the generator set is in use? As a generator manufacturer, let Xiaobian take you to understand the skills to prevent oil leakage of the generator set!

粘補膠治漏法。油箱水箱油管水管因決裂或砂眼氣孔等引起小滲漏，可用粘補膠涂改在清洗潔凈的破害處即可。

Glue patching and leakage control method. If the oil pipe and water pipe of the oil tank and water tank cause small leakage due to cracks or sand holes, it can be applied with adhesive to clean the damaged area.

加墊治漏法。發電機組里的油管接頭防漏墊圈處漏油，可在防漏墊圈的兩端加一層雙面潤滑的薄塑料墊，用力擰緊即可防漏。

Padding and leakage control method. The oil pipe joint in the generator set has oil leakage at the leak-proof gasket. A thin plastic pad with double-sided lubrication can be added at both ends of the leak-proof gasket, and the leakage can be prevented by tightening it firmly.

以抽治漏法。發電機組的油箱底殼氣缸蓋齒輪室蓋曲軸箱后蓋等多處紙墊滲漏時，若紙墊無缺接合面清潔，可在紙墊雙面抹上一層黃油，擰緊螺栓即可防漏；如換新紙墊，把新紙墊放在柴油中浸泡10分鐘后取出擦凈，在接合面上抹一層黃油再裝上。

The leakage shall be treated by pumping. In case of leakage of several paper pads such as the oil tank bottom, cylinder head, gear chamber cover, crankcase rear cover, etc. of the generator set, if the paper pad is clean without missing the joint surface, a layer of butter can be applied on both sides of the paper pad, and the bolts can be tightened to prevent leakage; If the paper pad is replaced, put the new paper pad in diesel oil for 10 minutes, take it out and wipe it clean, apply a layer of butter on the joint surface and then install it.

漆片液治漏法。柴油機油箱水箱曲軸箱等接縫處滲漏，可將漆片在酒精里浸泡后，把漆片液涂改在清洗潔凈的接縫處即可。

Lacquer liquid leak control method. If there is leakage at the joint of the crankcase of the diesel engine oil tank, the paint can be soaked in alcohol and then the paint can be painted on the clean joint.

厭氧膠治漏法。柴油機上的通氣螺栓雙頭螺栓等處出現滲漏時，可用厭氧膠涂改在清洗潔凈的螺栓螺紋處或螺孔里，能很快固化構成薄膜，填充零件空隙；此法用于柴油機高壓油管接頭螺紋處治漏效果更 好。

Anaerobic glue leakage control method. When leakage occurs at the breather bolt stud on the diesel engine, anaerobic adhesive can be applied to the cleaned bolt thread or screw hole, which can quickly solidify to form a film and fill the part gap; This method has a better effect on the leakage treatment of the high pressure oil pipe joint thread of diesel engine.

液態密封膠治漏法。柴油機上出現固體墊圈缺陷而構成的界面性滲漏和破壞性滲漏時，用液態密封膠涂改在清洗潔凈的固體墊圈結合面上，固化后構成均勻穩定連續黏附的可剝性薄膜墊圈，可防滲漏。

Liquid sealant leakage control method. In case of interfacial leakage and destructive leakage caused by solid gasket defects on diesel engine, liquid sealant shall be applied to the clean solid gasket joint surface, and after curing, the peelable film gasket with uniform, stable and continuous adhesion can be formed to prevent leakage.

尺度康復膠治漏法。柴油機的軸與軸套軸承與軸承座閥與閥痤自緊油封填料等處滲漏時，可用尺度康復膠涂改在清洗潔凈的協作件磨損部位，固化后構成耐磨機械強度較高的薄膜層，再進行機加工康復零件的幾何形狀和協作精度，可解決滲漏。

Scale rehabilitation glue leakage treatment. In case of leakage at the shaft and shaft sleeve bearing of the diesel engine, the bearing seat valve and the valve cone self-tightening oil seal filler, etc., the scale rehabilitation adhesive can be applied to the worn part of the cleaned collaboration part, and the solidified film layer with high wear resistance mechanical strength can be formed, and then the geometric shape and cooperation precision of the machined rehabilitation part can be processed to solve the leakage.

有了煤氣發電機組上面的小總結，希望對廣大客戶有所幫助，如果有什么不理解的或者尋求幫助的請點擊我們的網站：http://icea.com.cn或者來電咨詢，我們會盡全力為您解決

With the above summary of gas generator set, I hope it can help our customers. If you have any questions or need help, please click our website: http://icea.com.cn Or call for consultation, and we will do our best to solve it for you