關于交流柴油發電機的保養，雖然柴油發電機保養是很少需要進行，但是我們也是建議要作定期的檢查及清潔。對線圈的絕緣性能在第一次使用之前作測試。

Regarding the maintenance of AC diesel generators, although diesel generator maintenance is rarely required, we also recommend regular inspections and cleaning. Test the insulation performance of the coil before the first use.

如發電機停機備用，則視乎存放地點的溫度，3-6個月檢測絕緣度一次，在高溫度地區，當機器不使用時安裝發熱器來驅溫，將有助于保持線圈的乾燥。

If the generator is shut down for backup, the insulation degree should be checked every 3-6 months depending on the temperature of the storage location. In high temperature areas, installing a heater to drive the temperature when the machine is not in use will help keep the coils dry.

如交流柴油發電機裝有空氣過濾器則要視乎機址環境來進行定期的視察，如需進行清潔，把過濾器的材料拆下來，把材料浸或沖洗：可加入適當?shù)某蹌┲钡讲牧锨瑑魹橹?。在裝回去之前要把材料完全弄乾。

If the AC diesel generator is equipped with an air filter, regular inspections should be carried out depending on the site environment. If cleaning is required, remove the filter material and soak or rinse it: appropriate cleaning agents can be added until the material is clean. Before installing it back, completely dry the materials.

再者，交流柴油發電機的內外都應定期清潔，而清潔的頻率則要視乎機器所在地的環境。當要清潔時可按下列步驟進行。將所有電源斷開，把外表所有的塵、污物、油積、水及任何液體擦掉，通風網也要清潔干凈，因?yàn)檫@些東西進入線圈，這樣就會使線圈過熱或破壞絕緣。塵和污物較好用吸塵器吸掉，不要用吹氣或高壓噴水來清潔。

Furthermore, both the inside and outside of the AC diesel generator should be regularly cleaned, and the frequency of cleaning should depend on the environment where the machine is located. When cleaning, follow the following steps. Disconnect all power sources, wipe off all dust, dirt, oil, water, and any liquids on the surface, and clean the ventilation net thoroughly, as these things can enter the coil, causing it to overheat or damage the insulation. It is better to use a vacuum cleaner to remove dust and dirt, and do not use blowing air or high-pressure water spray to clean.

使用環境的氣溫對柴油發電機組的磨損也是有影響的。氣溫高時發動機易過熱，潤滑油粘度低，零件的磨損便增加。氣溫低時潤滑油粘度變大，柴油發電機組起動困難，工作時冷卻水不能保持正常溫度，增加零件的磨損和腐蝕。柴油機在低溫起動時，磨損更為嚴重。柴油發電機組的工作溫度是影響磨損的重要因素之一。在使用過程中，由于冷卻系統結構的限制，工作負荷及轉速的變化，環境溫度的改變等因素，使柴油發電機組工作溫度的變化范圍很大。實踐表明，冷卻水溫度控制在75～85℃，潤滑油溫度在75～95℃時一為有利

The temperature of the operating environment also has an impact on the wear and tear of diesel generator sets. When the temperature is high, the engine is prone to overheating, the viscosity of lubricating oil is low, and the wear of parts increases. When the temperature is low, the viscosity of lubricating oil increases, making it difficult to start the diesel generator set. During operation, the cooling water cannot maintain normal temperature, which increases the wear and corrosion of parts. Diesel engines experience more severe wear during low-temperature starting. The working temperature of diesel generator sets is one of the important factors affecting wear. During use, due to the limitations of the cooling system structure, changes in working load and speed, changes in ambient temperature, and other factors, the operating temperature of diesel generator sets varies greatly. Practice has shown that controlling the temperature of cooling water at 75-85 ℃ and lubricating oil at 75-95 ℃ is advantageous

感謝您的閱讀，此文的文章來源：煤氣發電機組更多的內容和問題請點擊：http://icea.com.cn 我們會繼續努力的為您提供服務，感謝您的支持！

Thank you for reading. The source of this article is: Gas Generator Set. For more information and questions, please click: http://icea.com.cn We will continue to work hard to provide you with services. Thank you for your support!